ANALYSIS OF LUBRICANT OIL CHARACTERISTICS USING THE BALL FALLING RELATIVE MOTION METHOD ON TEMPERATURE VARIATIONS
Journal Title: Engineering and Technology Journal - Year 2022, Vol 7, Issue 10
Abstract
The purpose of this research is to analyze the viscosity/viscosity of lubricating oil using the relative motion method of falling balls at various temperatures. This research is using experimental method. Where the test is carried out using temperature variations of 320C, 500C, 600C and 800C, steel balls with varying diameters, including 9.50 mm, 8.00 mm, 6.00 mm and 4.80 mm as well as variations in the viscosity of lubricating oil, including SAE. 10, SAE 40, SAE 90 and SAE 140. Data analysis used the method of calculating the fluid resistance equation of Stokes' law and the equation of motion from Newton's second law. The Stokes law equation by taking the example of a lubricant with a viscosity of SAE 10 is obtained for a steel ball diameter of 9.50 mm to obtain a fluid resistance of 7.159.200 m/s2, a steel ball with a diameter of 8.00 mm to obtain a fluid resistance of 6.028.800 m/s2, for a steel ball with a diameter of 6.00 mm obtained a fluid resistance of 4.521.600 m/s2, for a steel ball with a diameter of 4.80 mm, a fluid resistance of 3.617.280.000 m/s2 was obtained. It can be seen that at a certain viscosity value the weight of the steel ball will affect the fluid resistance, the greater the weight of the steel ball, the greater the fluid resistance value and vice versa. The equation of Newton's second law of motion shows that the lubricating oil with SAE 10 with 3.5 gram steel ball at a temperature of 32 is 17.92 gr.mm/s2, a temperature of 500C is 2471.8 gr.mm/s2, a temperature of 600C is 25396 ,82 gr.mm/s2, temperature 800C is 28000 gr.mm/s2. For the weight of the steel ball 2.1 grams at a temperature of 320C is 7609.98 gr.mm/s2, a temperature of 600C is 5555.5 gr.mm/s2, a temperature of 800C is 13884.15 gr.mm/s2. The results of the above calculations indicate that the viscosity value will decrease or decrease with increasing temperature applied to the lubricant, thus the flowability of the lubricating oil will increase faster.
Authors and Affiliations
Reinyelda D. Latuheru, Peter Sahupala,
Keywords
Related Articles
- EP ID EP716517
- DOI 10.47191/etj/v7i10.01
- Views 51
- Downloads 0
Design and Implementation of a Reliable and Secure Wireless CCTV Camera Network for the Main Administration Building, Federal Polytechnic Offa
This paper presents techniques for configuring, interfacing and networking of a wireless IP-based camera for real-time security surveillance systems for the main administration building of the Federal Polytechnic Offa, K...
Literature Review of the Green Building Concept of the Minister of PUPR RI Regulation Number 21 of 2021 concerning Evaluation Performance Building Building Green
The green building concept has been adopted as the main approach in the development of this project. The purpose of this final project is to analyze and implement the green building concept based on the Regulation of the...
The Conventional Oil-Water Separator as A Polluter Due to Lack of Maintenance – A Case Study
In addition to the common knowledge that lack of maintenance of conventional oil-water separators causes release of excessive amounts of oil in the effluent wastewater, this study has revealed that excessive amounts of o...
Sustainable Fishing Livelihoods: Exploring the Potential of Sail Technology Using Computational Fluid Dynamic in Traditional Fishing Boats
The potential of using sails and Computational Fluid Dynamics (CFD) to improve the sustainability of traditional fishing boats in the Maluku region. This study highlights the importance of cost-effectiveness and environm...
MECHANICAL BEHAVIOUR OF FERROCEMENT LIGHTWEIGHT BANANA FIBRE CONCRETE UNDER UNIAXIAL BENDING
To obtain lightweight and environmentally friendly building materials that can be produced quickly at low cost, among others, can be obtained through the use of natural fiber based ferrocement concrete technology. The us...