Investigating the strength and deformability of the node that connects precast slabs and monolithic joists in a flat precast-monolithic flooring slab
Journal Title: Восточно-Европейский журнал передовых технологий - Year 2019, Vol 4, Issue 1
Abstract
<p><span style="font-family: 'Times New Roman'; font-size: small;">The paper reports a study into the strength and deformability of the node that connects precast slabs and monolithic flooring joists in a flat precast monolithic floor based on the work of dowel pins. Current regulations for the design of reinforced concrete structures do not take into consideration the calculation of nodes that connect precast-monolithic structures in flat floors using dowel pins. </span></p><p><span style="font-family: 'Times New Roman'; font-size: small;">We have devised a procedure of experimental research that accounts for the specificity in the operation of a precast slab that forms a floor’s part. It was established that a change in the type of supports changes parameters for the stressed-strained state of samples of a precast monolithic floor slab: relative deformations of concrete, deformations of samples, as well as strength.</span></p><p><span style="font-family: 'Times New Roman'; font-size: small;">Testing the samples of a precast monolithic floor slab has demonstrated reliable operation of both the junction and the normal cross-section of the slab. It was determined that the node that connects precast multi-hollow slabs and a monolithic flooring joist using dowel pins has a 1.42-fold strength margin. </span></p><p><span style="font-family: 'Times New Roman'; font-size: small;">The paper reports results from field testing a fragment of the frame of a building for the influence of vertical loads. It is shown that the development of deformations in the main bearing elements of a floor slab occurred almost in line with a linear dependence; they amounted to 18.55 mm (for the central precast slab of a floor slab’s center) and 14.64 mm (for the bearing flooring joist). These deformations are more than 2 times less than the permissible value for vertical deformations (deflection) for these elements, which is equal to 40 mm.</span></p><p><span style="font-family: 'Times New Roman'; font-size: small;">The results from field testing have led to a conclusion on that the precast and monolithic elements in the floor slab’s disk operate as a solid structure. The tests did not detect any mutual displacements of the side ends of precast slabs relative to the load-bearing flooring joists. </span></p><p><span style="font-family: 'Times New Roman'; font-size: small;">The procedure for calculating the strength of the connecting node has been improved. A change in the strength of samples of a flat precast monolithic floor slab is accounted for by the introduction of an appropriate coefficient for the operation conditions of transverse reinforcement, which is equal to 0.8.</span></p>
Authors and Affiliations
Olena Butska, Tetiana Nikiforova, Mykola Makhinko, Svitlana Shekhorkina
Keywords
Related Articles
- EP ID EP666804
- DOI 10.15587/1729-4061.2019.174476
- Views 76
- Downloads 0
Improving a resourcesaving surfacing technology using two ribbon electrodes with a controlled transfer of electrode's metal
<p>This paper reports results of research into a resource-saving technology of surfacing with two ribbon electrodes with a controlled transfer of the electrode's metal from the end sides of ribbon electrodes and with an...
Examining a possibility of using purple amaranth in the technology for products made of yeast dough
<p>It was experimentally found that additives of purple amaranth (APA) have high enzyme activity, which is proved by high activity of the amylase complex: maltose number of 5 % water extract from dry foliage of purple am...
Evaluation of dynamic properties of gas pumping units according to the results of experimental researches
Experimental studies of the dynamic properties of gas pumping units (GPU) of various types, which allowed us to obtain GPU acceleration curves and determine the parameters of the transfer function through various transmi...
Studying the quality of drill pipes clamped in a wedge clamp
<p class="Default">Much attention has been recently paid to institutional measures aimed at improving quality of products related to petroleum machine building, in particular, the implementation of quality management sys...
Impoving energy characteristics of the welding power sources for TIG-AC welding
This paper proposes a circuit solution and a control algorithm for a welding power source for TIG-AC welding with improved energy characteristics. The source is made using a welding transformer and a low-voltage series a...