Investigation of Thermal and Viscoelastic Properties of Polymers Relevant to Hot Melt Extrusion, IV: Affinisol™ HPMC HME Polymers
Journal Title: AAPS PharmSciTech - Year 2016, Vol 17, Issue 1
Abstract
Most cellulosic polymers cannot be used as carriers for preparing solid dispersion of drugs by hot melt extrusion (HME) due to their high melt viscosity and thermal degradation at high processing temperatures. Three HME-grade hydroxypropyl methylcelluloses, namely Affinisol™ HPMC HME 15 cP, Affinisol™ HPMC HME 100 cP, and Affinisol™ HPMC HME 4 M, have recently been introduced by The Dow Chemical Co. to enable the preparation of solid dispersion at lower and more acceptable processing temperatures. In the present investigation, physicochemical properties of the new polymers relevant to HME were determined and compared with that of Kollidon® VA 64. Powder X-ray diffraction (PXRD), modulated differential scanning calorimetry (mDSC), thermogravimetric analysis (TGA), moisture sorption, rheology, and torque analysis by melt extrusion were applied. PXRD and mDSC showed that the Affinisol™ polymers were amorphous in nature. According to TGA, the onset of degradation for all polymers was >220°C. The Affinisol™ polymers exhibited less hygroscopicity than Kollidon® VA 64 and another HPMC polymer, Methocel™ K100LV. The complex viscosity profiles of the Affinisol™ polymers as a function of temperature were similar. The viscosity of the Affinisol™ polymers was highly sensitive to the shear rate applied, and unlike Kollidon® VA 64, the viscosity decreased drastically when the angular frequency was increased. Because of the very high shear rate encountered during melt extrusion, Affinisol™ polymers showed capability of being extruded at larger windows of processing temperatures as compared to that of Kollidon® VA 64.
Authors and Affiliations
Simerdeep Singh Gupta, Nayan Solanki, Abu T. M. Serajuddin
Keywords
Related Articles
- EP ID EP682150
- DOI 10.1208/s12249-015-0426-6
- Views 95
- Downloads 0
Simultaneous Determination of Acetaminophen and Synthetic Color(s) by Derivative Spectroscopy in Syrup Formulations and Validation by HPLC: Exposure Risk of Colors to Children
Analytical reagent grade sodium hydroxide and concentrated hydrochloric acid were procured from Qualigens, Mumbai, India. Methanol and acetonitrile (HPLC grade) were purchased from Merck Limited, Mumbai, India. The stand...
Development and Optimization of a Novel Prolonged Release Formulation to Resist Alcohol-Induced Dose Dumping
Alcohol-induced dose dumping is a serious concern for the orally administered prolonged release dosage forms. The study was designed to optimize the independent variables, propylene glycol alginate (PGA), Eudragit RS PO...
Simulation of In Vitro Dissolution Behavior Using DDDPlus™
Dissolution testing is a performance test for many dosage forms including tablets and capsules. The objective of this study was to evaluate if computer simulations can predict the in vitro dissolution of two model drugs...
Development and Characterization of Sorbitan Monostearate and Sesame Oil-Based Organogels for Topical Delivery of Antimicrobials
The online version of this article (doi:10.1208/s12249-014-0223-7) contains supplementary material, which is available to authorized users.
An Investigation into the Effect of Fine Lactose Particles on the Fluidization Behaviour and Aerosolization Performance of Carrier-Based Dry Powder Inhaler Formulations
The effect of milled and micronized lactose fines on the fluidization and in vitro aerosolization properties of dry powder inhaler (DPI) formulations was investigated, and the suitability of static and dynamic methods fo...