Optimization the Spray-Drying Process of Moldavian Balm Plant Extract using Response Surface Methodology and TOPSIS Method
Journal Title: Journal of Agricultural Machinery - Year 2020, Vol 10, Issue 2
Abstract
Introduction Dracocephalum moldavica L. is an annual plant with blue or white flowers and fragrant leaves which belongs to the family of Lamiaceae with the height of up to 80 cm. This plant is native to Central Asia and is accepted in Central and Eastern Europe. In Iran, it is mainly grown in the province of West Azarbaijan and the Alborz Mountains. The essential oils and extracts derived from the secondary metabolisms which are mainly used in the pharmaceutical industry, dietary, cosmetic, flavoring and also as tea and beverage with sugar or honey. The liquid extract of the herb contains a high percentage of water, which should evaporate to increase shelf-life, easy transport, handling and storage, the ease of standardization and preservation of the product quality. On the other hand, the active compounds of the extracts are affected by temperature, oxygen, light and enzymes. Therefore, because of the uses and benefits of herbal extracts, they need to be dried by a practical and effective method like spray drying. In literature still there are no studies taking into account to the comparisons between RSM and TOPSIS as two important optimization methods. So, as the main objective of the present work, the effects of moisture content, drying performance, total phenol content, total flavonoid content and antioxidant activity have been surveyed. Finally, the optimal point of each process variable was presented by two optimization methods. Materials and Methods Aerial parts of Moldavian balm plant were cleaned and drying of plant was carried out under shade and thin layer conditions. The extraction of Moldavian balm was obtained by maceration method using ethanol 50 % (v/v), plant to solvent ratio of 1/10 (w/v). After 48h, the extract was concentrated in a rotary evaporator (Buchi Rotavapor R-205, Switzerland) to obtain a solid concentration of 6%. The used carrier was: Maltodextrin and apple pectin. Different ratios of carrier were prepared, then the ratio was added to distilled water and stirred by a magnetic stirrer. Finally, the solution was mixed with extract. The drying of Moldavian Balm plant extract was performed using a spray-dryer (Büchi B-191, Switzerland) with co-current flow regime. The powders provided by the spray drying were stored in refrigerator until they were needed for the experiment. Results and Discussion The results of variance analysis showed that the Box-Behnken design with the second-order model has led to the meaningfulness of the model, insignificant of the Lack of Fit and the appropriate correlation coefficient for each of the responses. A total number of 15 experiments were conducted to investigate the effect of process variables such as inlet air temperature, compressed air flow rate and concentration of carriers on moisture content, drying performance, total phenolic content, total flavonoid content and antioxidant activity of Moldavian balm powder. Inlet air temperature and compressed air flow rate had the most significant effect on moisture content and drying performance, while Chemical properties of the powder affected by changing the concentration of carriers. Optimization parameters of the spray drying process was performed using surface response and TOPSIS methods. The optimum predicted conditions in the response surface method and TOPSIS method were obtained at inlet air temperature, compressed air flow rate and concentration of carrier (152.5-150°C), (8.046-7.5 lit min-1) and 20%, respectively. Conclusion By comparing two methods, it can be concluded that although they could provide the same optimum points, the RSM is more efficient. Because RSM offers a mathematical model that can be used at any desired point of variables to predict the output quantities as well as describing the process trend, while TOPSIS method is unable to predict the process trend and only provides the ranking of alternatives.
Authors and Affiliations
E. Rahmati,F. Sharifian,M. Fattahi,Gh. Najafi,
Keywords
Related Articles
- EP ID EP717956
- DOI https://doi.org/10.22067/jam.v10i2.78344
- Views 57
- Downloads 0
Optimization and Analysis of a λ-Formed Straight Line Linkage for Design of Reversible Disk Plow.
Disk plows are one of the most important tillage tools. Two way (reversible) disk plows can perform continues plowing. So they can save time and costs and hence improve overall efficiency. In this study, a “two-way” disk...
The Effect of Harvesting Time in Moghan on Corn Losses and its Prediction using Fuzzy Logic
Introduction Corn harvest losses are imposed by several factors, the most important of which is harvesting-time. Since the harvesting-time is coincident with the rainy season, it is necessary to appropriately estimate th...
Challenges and Opportunities in Development of Agricultural Mechanization in Ahvaz County using SWOT Method
IntroductionAgricultural mechanization is defined as the use of energy and production resources, machinery and equipment in agriculture. Modern agriculture is heavily dependent on mechanization, and machinery, equipment,...
Detection of Cucumber Fruit on Plant Image Using Artificial Neural Network
The main purpose of this study was to provide a method for accurately identifying the position of cucumber fruit in digital images of the greenhouse cucumber plant. After balancing the brightness histogram of the desired...
Investigation on the Capability of GreenSeeker Sensor in Predicting Nitrogen Status and Fractional Vegetation Cover of Spinach Crop
Fractional vegetation cover (FVC) and normalized difference vegetation index (NDVI) are the most important indicators of greenness and have a strong correlation with green biomass. The objective of this study was to eval...