Re-Extension of 200 MW Turbine Cast Casing Service
Journal Title: Проблеми машинобудування - Year 2019, Vol 22, Issue 2
Abstract
To date, the fleet service life of a significant number of DTEK Energy power units is ex-ceeded. In particular, this relates to the structural components of the K-200-130-3 steam turbine of the power unit No. 9 of DTEK Luganskaya TPP. There is a need to make a decision on the admissibility of further exploitation. This requires a comprehensive study of the technological state of the base metal and the check calculation of its most critical high-temperature elements. A complex of such works was performed earlier in 2009. A special feature of re-extending the service life of this power unit is the super long fleet equipment operating time, presence of damages in the form of cracks and crack surfaces in the high- and intermediate-pressure cylinder casings, as well as the active involvement of equipment to operate in maneuverable modes when covering peaks of electrical load. This paper assesses the residual life of casings on the basis of three-dimensional models of the K-200-130-3 steam turbine high-pressure (HP) and intermediate- pressure (IP) cylinder casings. In doing so, the paper takes into account the actual operating conditions according to the damage data obtained from the results of inspecting the power equip-ment metal condition during preventive maintenance overhauls. The calculation of tem-perature fields is performed for typical operation modes, namely stationary operation at nominal power and starts from cold, warm, and hot states. The boundary value problem of heat conduction was solved using the finite element method of computational domain discretization. The calculation of the stress-strain state (SSS) was made taking into ac-count the effects of the main types of forces − temperature stresses, uneven temperature fields, forces from the steam atmosphere pressure, supporting forces. The maximum stress intensities for all the investigated modes of operation are observed in the toroidal parts of cylinder casings in the region of steam admission and correspond to the crack formation zones that were determined during the non-destructive testing of the metal. The assess-ment of long-term strength and low-cycle fatigue resistance showed that the residual life of the high-pressure cylinder (HPC) casing is satisfactory, and allows extending the op-eration by 100 thousand hours with standard safety factors. For the intermediate-pressure cylinder (IPC) casing, the residual life is 50 thousand hours with reduced safety factors.
Authors and Affiliations
Olga Yu. Chernousenko, Dmitriy V. Ryndyuk, Vitaliy A. Peshko
Keywords
Related Articles
- EP ID EP622775
- DOI 10.15407/pmach2019.02.014
- Views 62
- Downloads 0
Calculated Evaluation of the Thermal Physical Properties of Nitrogen as a Working Fluid of Cryogenic Piston Engines. Heat Conductivity Calculation
Vehicles with internal combustion engines (ICEs) used by many enterprises or high fire hazard facilities (airports, docks, elevators, chemical plants, refineries) can be sources of ignition due to the peculiarity of thei...
Calculation of Indicators of Reliability of Technical Systems by the Typical Structural Scheme Method
A method for calculating the indicators of structural reliability of systems with a large number of elements is presented. The method is based on the use of typical structural schemes, reflecting the concept of connectio...
Numerical analysis of stress-strain state of vertical cylindrical oil tanks with dents
The destruction of vertical cylindrical tanks results in both human and economic losses. Despite constant improvement of the manufacturing technology of cylindrical tanks, a complete analysis of the influence of various...
Experimental Study of the Effects of a Constant and Variable Electric Fields on the Strength Properties of the Blade Steel Surface Layer
It is known that in wet steam turbines the wet steam flow is electrified when passing through the turbine flow path. In this, the mutual electrification of the condensed moisture flow and flow path surfaces occurs. Until...
Chaotic Oscillations of a Kinematically Excited Flat Shell During Geometrically Non-linear Deformation
We study the forced oscillations of a cantilevered flat shell of constant curvature. These movements are excited by a kinematic periodic embedding motion. To describe geometrically non-linear deformation, the non-linear...