Study of The Vapor Thermo-Compressor to Reduce Energy Consumption in the Sugar Production Line using Computational Fluid Dynamics
Journal Title: Journal of Agricultural Machinery - Year 2020, Vol 10, Issue 2
Abstract
IntroductionLarge industrial factories often discharge significant quantities of low-pressure steam (dead steam) into the atmosphere, which causes energy losses. Retaining low-pressure steam content reduces boiler load, resulting in energy savings and lower costs for the fuel consumption (for example, gas consumption bill in a factory). The boosted-pressure steam is used in processes such as distillation, hot water production, space heating or vacuum generation. If the vapor pressure for the intended application is low, a thermo-compressor is able to increase the pressure and temperature to the required level. Thermo-compressors are a special type of gas compressor that uses an actuator to compress secondary fluid and does not have any blades or moving parts. The accurate prediction of the thermo-compressor performance improves the reliability of this process and increases its efficiency.Materials and MethodsTwo important characteristics for the current thermo-compressors are entrainment ratio (ER) and compression ratio (CR). The first is the dimensionless mass flow rate, and the second is the dimensionless pressure. The wet steam theory as a classic theory is used by Wolmer-Frankel-Zeldovich to calculate the amount of liquid particles. In order to select the best geometry for the thermo-compressor among all possible geometries, the performance of each model must be compared with other models. In following, the case that includes characteristic parameters associated with the target values has been selected.The commercial Ansys Fluent Versions 15, based on the finite volume method (FVM) was used to simulate and monitoring the flow behavior inside the thermo-compressor. The governing partial differential equations (PDE) were solved implicitly using a density-based solution. The convective heat transfer terms were discriminated based on the second-order upwind scheme. The non-linear governing equations were solved using the implicit coupling solver and the standard wall function was used near the wall. Given the three-dimensional flow for steam, the equations of mass conservation, momentum, and energy were written. The Realizable  model was used to simulate turbulences in the flow.Results and DiscussionA summary of the results is presented in terms of the results of pressure, velocity magnitude, Mach number and temperature. A general understanding of this characteristic for a thermo-compressor is extremely important for recognizing the fluid flow inside it, and it is very useful for practical use. Pressure is the most important factor in the recharge section of a thermo-compressor. Increasing the recharge vapor pressure in a thermos-compressor revival the dead steam and increases the steam efficiency. The revival steam can be used in other parts because of their high thermal content. Another important factor in the study of flow behavior inside the thermocouple is velocity magnitude. This quantity, which is closely related to the concept of momentum inside the thermocouple, had high influences from high pressure inputs as well as the thermo-compressor geometry. The highest amount of velocity occurs after the initial nozzle and had a very high magnitude (1000 ms-1), which was also remarkably high in Monnet's terms. Another important characteristic of a flow is the temperature of the stream. The high input temperature associated with motive vapor at the outlet of the primary nozzle was sharply reduced, even in some section reached to 110 °Kelvin. Due to the very high flow momentum in this section, the fluid phase remained gas and it can be justified from the point of view of the fluid dynamics.ConclusionConsidering the importance of thermodynamic properties of steam in conversion and industries, it would be extremely beneficial to fully understand the interactions inside the thermocouple compressor. The importance of the discussed characteristics is more specific when there is a close relationship between each of these factors and energy consumption in a factory or in any industrial production unit. It was observed that the designed thermos-compressor was able to increase the velocity and temperature in a desirable range for the conversion of non-consumable vapor to the pressure and temperature. It was concluded that the Realizable  model due to the prediction of the jet characteristics appearing in the flow regimes for axial symmetry had a high ability to simulate fluid flows inside the thermos-compressor.
Authors and Affiliations
A. Rezvanivand fanaei,A. Hasanpour,A. M. Nikbakht,
Keywords
Related Articles
- EP ID EP717957
- DOI https://doi.org/10.22067/jam.v10i2.76872
- Views 48
- Downloads 0
Performance Evaluation of a Solar Dryer with Finny, Perforated Absorber Plate Collector Equipped with an Air Temperature Control System for Dill Drying
Dill is one of the most important plants in the world because of its medicinal properties and it is widely used as a vegetable in the most parts of Iran. In the present study a new solar dryer with finny, perforated abso...
Fabrication and evaluation of a reservoir tillage machine to reduce runoff from farms with sprinkler irrigation systems
IntroductionNowadays, in a lot of farm land due to reasons such as high density, heavy textured soils, steep terrain and a large body of water at each irrigation, rapid and complete absorption of water in the soil does n...
Implementation of a Machine Olfaction for the Detection of Adulteration in Cow Ghee
IntroductionOne the most important discussions of the world community is the importance and the role of edible oils in the nutrition and physical health of individuals, especially in the prevention of cardiovascular dise...
Studying and optimizing the biodiesel production from mastic oil aided by ultrasonic using response surface method
Introduction Biodiesel is a promising renewable substitute source of fuel produced from tree born oils, vegetable based oils, fats of animals and even waste cooking oil, has been identified as one of the key solutions fo...
Optimization of Refinement Operations of Sugarcane Harvester Hydraulic Oil
The purpose of this study was to model and optimize the offline refinement operations of sugarcane harvester hydraulic oil using RSM. For this purpose, the effects of independent variables of operating hours (250, 500 an...