The Effect of the Knife Tacking Type on the Process of Producing Microcrystalline Cellulose
Journal Title: Lesnoy Zhurnal (Russian Forestry Journal) - Year 2024, Vol 2, Issue 2
Abstract
The article shows the possibility of intensifying the process of producing microcrystalline cellulose via pregrinding of fibrous semi-finished products before hydrolysis. The technological factors determining the grinding of fibrous materials have been considered. The efficiency of the microcrystalline cellulose production process is influenced by the choice of its production technology. For grinding, a semi-industrial disc mill with a tacking with rectilinear and curvilinear knives has been used. Multiphysics models of the flow of fibrous mass in the grinding zone of a disc mill with different knife tacking patterns have been constructed. The morphological properties of the fiber have been measured on the Morfi Neo automatic fiber analyzer after grinding to 65 °SR. The nature of the change in the properties of bleached sulfate hardwood and softwood cellulose has been analyzed. It has been found that it is identical for all degrees of grinding, but the quantitative characteristics change to the greatest extent when grinding softwood cellulose using a tacking with rectilinear knives: the weighted average length of fibers decreases by 17 %, the width â by 14 %; the content of broken fibers increases by 22 %, the content of fines along the length â by 67 % and the fibrillation index â by 1.9 times. A comparative analysis of the values of the degree of polymerization depending on the knife tacking pattern has been carried out. The conditions for producing microcrystalline cellulose after grinding the fibrous mass in a semi-industrial disc mill, depending on the degree of grinding, have been determined. It has been shown that with an increase in the degree of grinding of the fibrous mass from 15 to 65 °SR, the degree of polymerization of microcrystalline cellulose decreases from 272 to 120, the concentration of hydrochloric acid â from 2.5 to 1.5 N and the duration of hydrolysis â from 120 to 90 min. The developed method for producing microcrystalline cellulose makes it possible to reduce the cost of chemical treatment of the fibrous mass (acid concentration, treatment duration and hydrolysis temperature) by 1.5 times.
Authors and Affiliations
Larisa V. Yurtayeva,Yuriy D. Alashkevich,Elena A. Slizikova,Evgeniy V. Kaplyov,Snezhana A. Pozharkova,
Keywords
Related Articles
- EP ID EP734357
- DOI -
- Views 55
- Downloads 0
Sibs Progeny of Curly Birch at the Zaonezhye Forest Seed Orchard
The article reports the results of studies on the growth and development of curly birch sibs progeny (produced through controlled pollination) aged 35 and 15 years growing in the Zaonezhye forest seed orchard (sites 1 an...
The Engineering Procedure for Calculating the Plant for Betulin Extraction from Birch Bark
The analysis of the current state of the process of betulin extraction from birch bark has shown the relevance of the implementation of periodic extraction technology using toluene as a solvent at small enterprises of th...
The State of Forests Growing on Iron Oxide-Saturated Soils of Azerbaijan
Today Azerbaijan focuses on the non-oil sector development. The mining industry is actively growing, to become one of its driving forces. This is detrimental to the ecology of the region. The intensive mining activity ha...
Modeling the Process of Sawn Timber Drying
The article considers the problem of sawn timber drying. The relevance of research is driven by the need to improve the automated process control system for drying sawn timber on the basis of modern information technolog...
Creation of Forest Cultures of Crimean Pine (Pinus pallasiana D. Don) on the Hilly Sands in the Steppe Zone of Russia
Forest crop cultivation of Crimean pine (Pinus pallasiana D. Don) was implemented in 2009â2020 on sandy and sand included soils in the steppe zone of the European part of Russia. During the analysis of the reasons for...