THE PROSPECTIVE PROCESSING LINE FOR THE PREPARATION OF COMPLETE FE ED FOR LONG-TERM STORAGE
Journal Title: Journal of Mechanical Engineering Research & Developments (JMERD) - Year 2018, Vol 41, Issue 4
Abstract
An important condition for increasing the livestock production efficiency and production of livestock products and reducing their cost is full-value feeding, the provision to the farm animals complete multicomponent feed mixtures. Such mixtures are much better digested by the livestock which contributes to a 10-14% increase in their production efficiency. Numerous studies have revealed that it is most practical to feed large cattle with full-value feed mixtures prepared immediately before dispensing, which is not always possible in the production conditions. This especially applies to regions where the winter is a so-called housing season for the livestock. It is extremely difficult to provide the farm animals with a full-fledged diet during that period. To avoid feed-related problems, it is necessary to create a preliminary stock of fodder with sufficiently preserved nutrients. In the Amur Region, multicomponent silage, haylage, and different mixed feeds are used for the full-value feeding of the livestock. At the same time, the delivery of silage and haylage in low-temperature conditions is both laborintensive and energy-intensive, since the air temperature in this period is about -25...35°C. During the transportation of these kinds of fodder, high losses are observed due to their thawing before feeding. In accordance with the above, it can be concluded that in order to provide animals with full-value feed, it is necessary to use technologies that allow maximum preservation of nutritional properties of feed and ensure its long-term storage. One of the methods that contribute to the solution of this problem is adaptive drying of feed, which results in the preservation of the maximum amount of nutrients in their contents and the reduction in labor input required to transport the mixtures to the place of feeding during the cold winter period. The aim of the research is to increase the efficiency of preparation of livestock complete feed by developing the technology and means of mechanization for long-term storage. To solve this aim the following research tasks were defined: - to analyze advanced technologies and technical means for the production of feed for large cattle by reference to specific features of the food base and the natural production conditions of the Amur Region. - to justify prospective lines of development of existing ones and develop the new technical means for the preparation of feed and agricultural crops for long-term storage. The article in hand describes the prospective processing line for the proper preparation of the full-value feed for longterm storage which ensures the preservation of nutrients.
Authors and Affiliations
S. V. Shchitov, R. L. Sharvadze, T. A. Krasnoshchekova, E. I. Reshetnik, Yu. R. Samarina, , N. A. Kapustina
Keywords
Related Articles
- EP ID EP434705
- DOI 10.26480/jmerd.04.2018.12.16
- Views 60
- Downloads 0
INFLUENCE OF HEAT TREATMENT AND DEFORMATION ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES Cu-Ni-Sn ALLOY
This article present about studying on effect heat treatment and strain on mechanical properties of Cu-7Ni-7Sn alloy. This alloy is high elasticity alloy, advance characteristics of this alloy can obtain when associate h...
EFFECT OF DIFFERENT QUENCHING MEDIA ON MECHANICAL PROPERTIES OF AISI 1018 LOW CARBON STEEL
In this work, the mechanical properties of AISI 1018 low carbon steel after been treated by different quenching media (water, boiling water, boiling salt water, ice water, ice salt water) were evaluated. The microstructu...
A STUDY ON THE FACTORS AFFECTING THE FLARE OF THE WELD WHEN WELDING THE STEEL WIRE
In this study, an equation for adjusting the parameters affecting the flare of the weld on the welding product was established. Based on the empirical research results, the factors affecting welding flux after using bend...
APPLICATION OF THE AUTOMATED SYSTEM-COGNITIVE ANALYSIS FOR SOLVING PROBLEMS OF GENETICS
This article describes an approach that provides the calculation of the amount of information in the genes about the characteristics or properties of different grape cultivars. A specific phenotypic property is considere...
INFLUENCE OF HEAT TREATMENT ON THE ABSORBED ENERGY OF CARBON STEEL ALLOYS USING OIL QUENCHING AND WATER QUENCHING
Carbon steel alloys are modified by heat treatment processes so that structural components are able to withstand and sustain external forces and loads which specified operating conditions and have desired useful life. In...