Wear Resistance Increase of Samples Tribomating in Oil Composite with Geo Modifier КGМF-1
Journal Title: Tribology in Industry - Year 2019, Vol 41, Issue 2
Abstract
Increase of wear resistance of different types of tribomating which are functioning in fluid lubrication is possible due to: choosing more expensive and high quality material of samples that is not always sensible; applying some wear resistant coatings on them; selection and formation of complex composition of oil additives. Due to nanomaterials development there is a possibility of efficient use of functional additives such as geo modifiers in tribology. Due to geo modifier-based oil composites use it’s not necessary to make any structural changes of machines mated parts though their wear resistance is increased. It requires the conducting of some experimental tribological research. It was found that oil media modified by a geo modifier increase the wear resistance of working surfaces of different types of tribomating. The use of geo modifier КGМF-1 (Katerynivka friction geo modifier -1 (patent of Ukraine №69657)) has been suggested. Lubrication quality of oil compositions based on М-10Г2К (M-10G2K) (motor oil of 10th viscosity grade, of group Г2К (G2K), for the CIS countries the oil grade conforms SAE 30) + КGМF-1 (4.0 - 4.5%) has been studied on a computer modernized four-ball friction testing machine ЧШМ-К1 (CHMK-К1). To evaluate the lubrication quality of the oil composite with the suggested geo modifier and to use the comparative analysis of the obtained results the research was conducted on commercial samples of base oil M-10G2K and oil composites M-10G2K + XADO Maximum for Diesel Truck (2.0 - 2.3%) (agent 2D sliding revitalization factor (RF) 100, revitalizant 1 Stage RF 100, metal conditioner RF 5.5), M-10G2K + cuprum glycerate (3.7 - 4.5%). Some average indices of wear, critical load, and welding load have been found. Samples division into 4 types of mating according to the following characteristic features: mobility, material hardness and friction area has been suggested for more accurate picture of wear resistance changes of samples tribomating which are functioning in base and modified oil. Lower friction torque of different samples couplings in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was recorded while using Friction machine 2070 SMT-1 with add-on module "ring-ring". The samples wear rate in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was studied by method of acoustic signal amplitude measurements directly from the friction zone by a commercially produced instrument of Brüel & Kjear company.
Authors and Affiliations
V. Aulin, S. Lysenko, O. Lyashuk, A. Hrinkiv, D. Velykodnyi, Y. Vovk
Keywords
Related Articles
- EP ID EP593767
- DOI 10.24874/ti.2019.41.02.02
- Views 87
- Downloads 0
Tribological Performance Optimization of Electroless Ni-P-W Coating Using Weighted Principal Component Analysis
The present investigation is an experimental approach to deposit electroless Ni-P-W coating on mild steel substrate and find out the optimum combination of various tribological performances on the basis of minimum fricti...
Tribological Behavior of Thermal Spray Coatings, Deposited by HVOF and APS Techniques, and Composite Electrodeposits Ni/SiC at Both Room Temperature and 300 °C
The Both the thermalspray and the electroplating coatings are widely used because of their high wear resistance combined with good corrosion resistance. In particular the addition of both micro particles or nano‐particle...
Eco-Friendly (Water Melon Peels): Alternatives to Wood-based Particleboard Composites
The aim of this study was to investigate the suitability of using water melon peels as alternatives to wood-based particleboard composites. The water melon peels composite boards were produced by compressive moulding usi...
Microstructure and Wear Analysis of FeBCr Based Coating Deposited by HVOF Method
Thermally sprayed coatings that are based on FeBCr-related alloy powders are widely used to improve properties such as the surface hardness and wear resistance of a variety of coated metal substrate materials. Gray cast...
Numerical Modeling of Disc Brake System in Frictional Contact
Safety aspect in automotive engineering has been considered as a number one priority in development of new vehicle. Each single system has been studied and developed in order to meet safety requirement. Instead of having...