Research into the impact of structural features of combustion chamber in energy-technological units on their operational efficiency
Journal Title: Восточно-Европейский журнал передовых технологий - Year 2018, Vol 5, Issue 8
Abstract
<p>The experimental studies of the influence of the degree of masonry development (geometry) and aerodynamics of the combustion chambers (circuits of combustion products removal) on the energy-technological indicators of the processes in the system gas-solid (in combustion chambers) were carried out.</p><p>The experimental research into the influence of geometry and aerodynamics of the combustion chamber on the energy-technological indicators in the system gas – solid body was conducted at the industrial large-scale fire bench.</p><p>It was shown that a decrease in the height of the working space of the combustion chamber, equipped with flat flame burners, affects the use of fuel due to heat exchange intensification, including direct convection. The dependence is caused by a decrease in heat losses with flue gases and due to a decrease in losses through the masonry.</p><p>It was established that at the height of the working space of 800÷1,000 mm of the combustion furnace, fuel consumption decreases by 20÷30 %.</p><p>The design of the combustion space of the furnace of continuous operation mode was developed. The distinctive feature of the furnace of the developed design is the elimination of discreteness and implementation of the stable continuous operation mode of the heating unit. The longitudinal channels were made on the lateral surfaces of the cars and the furnace along the entire length of the latter, which makes it possible to implement the continuous removal of combustion products from the combustion space through canalized hearth of the cars into the longitudinal lateral channels, made in the walls of the furnace. Additional aerodynamic compaction of the working space of the furnace is ensured at any speed of the motion of the cars.</p><p>It was found that energy-technological efficiency at the arch heating of the combustion units with flat flame burners and combustion products removal under the workpiece (lower smoke removal) is on average by 1.3 times higher than at use of the circuit of products removal above the workpiece (lateral smoke removal), which is used in currently operating furnaces.</p><p>The design was developed and the tunnel furnace was put into operation. It was for chemical and thermal treatment of metallic and non-metallic materials and products during their heating by the assigned schedule.</p>
Authors and Affiliations
Valeriy Nikolsky, Olga Oliynyk, Viktor Ved, Andrii Pugach, Ramzan Turluev, Oleksandr Alieksandrov, Viacheslav Kosarev
Keywords
Related Articles
- EP ID EP528206
- DOI 10.15587/1729-4061.2018.143316
- Views 49
- Downloads 0
STUDYING PATTERNS IN THE FLOCCULATION OF SLUDGES FROM WET GAS TREATMENT IN METALLURGICAL PRODUCTION
The influence of a solid phase concentration in the model sludges of wet gas purification, as well as the flocculant consumption, on a change in the solid phase sedimentation rate and the strength of floccules has been e...
Investigation and analysis of the possibility of diffusionless phase transformations in the surface layer of a part under the action of grinding temperatures
<p>The possibility of diffusionless phase transformations in the surface layer of the ground part under the influence of instantaneous grinding temperature is investigated and analyzed. This is important because the phas...
Development of the method for geometric modeling of S-shaped camber line of the profile of an axial compressor blade
The method for geometric modeling of the S-shaped camber line of the profile of an axial compressor blade, which is a compound curve formed from three sections, was developed. Each of these sections is modeled in the nat...
Studying the effect of concentration factors on the process of chemical metallization of powdered polyvinylchloride
<p>Influence of concentration of components of chemical metallization solutions on the process of copper reduction on activated polyvinylchloride surface has been studied. It has been established that changes in concentr...
Ensuring comfort microclimate in the classrooms under condition of the required air exchange
<p>We performed comparative analysis of regulatory documents, which relate to ventilation of school premises and operate in European countries at present. We showed the essential difference of the recommended air exchang...