Shear Bond Strength of Resin Bonded to Bleached Enamel Using Different Modified 35% Hydrogen Peroxides
Journal Title: Journal of Dental Biomaterials - Year 2015, Vol 2, Issue 4
Abstract
Statement of Problem: Bleaching systems with different concentrations and applications are widely used to improve the visual appearance of the teeth, but one of the complications of these materials is reduction of bond strength for immediately bonding to the bleached enamel. Objectives: The aim of this study was to evaluate the influence of using different modified hydrogen peroxide bleaching agents on the shear bond strength of composite resin bonded to the bleached enamel. Materials and Methods: Forty-eight sound extracted premolar teeth were collected, sectioned 1 mm below the CEJ to detach the root. The proximal surfaces of the teeth were flattened using diamond disks and silicon carbide papers to achieve flat homogeneous enamel surfaces without exposure to the dentin. The teeth were randomly divided into four groups as follows (n = 12): group 1: bleaching with 35% hydrogen peroxide gel; group 2: bleaching with 35% hydrogen peroxide gel contained (casein phosphopeptide-amorphous calcium phosphate (CPP-ACP); group 3: bleaching with 35% hydrogen peroxide gel combined with fluoride; and group 4: bleaching with 35% hydrogen peroxide applying one week before resin restoration placement. Composite resin, Clearfil AP-X (Kuraray, Tokyo, Japan), was bonded on each tooth in the mould (4 mm diameter × 3 mm height) using Clearfil SE Bond (Kuraray, Tokyo, Japan). After 24 hours of storage and 1000 cycles of thermocycling, the shear bond strength of the specimens at a cross-head speed of 0.5 mm/min was measured in MPa. Data were analyzed using ANOVA and Tukey’s post-hoc test. Results: The minimum and maximum mean shear bond strength values were observed in groups 2 (15.82 ± 4.41) and 4 (21.00 ± 3.90), respectively. Multiple comparisons of groups revealed no significant differences among the groups except between group 4 and all the other groups. The most common type of failure was adhesive. Conclusions: Using modified bleaching agents decreased the bond strength of the composite resin to the enamel when it was used immediately after bleaching.
Authors and Affiliations
H Moosavi, M Shaykhvasy
Keywords
Related Articles
- EP ID EP248927
- DOI -
- Views 64
- Downloads 0
Effect of Different Bleaching Techniques on Microleakage under orthodontic Brackets: In Vitro Study
Statement of problem: Numerous studies report significant changes in tooth color that occur during orthodontic treatment. The adverse effects of bleaching procedures during orthodontic treatments have not been studied co...
Effect of Combined Calcium Hydroxide and Accelerated Portland Cement on Bone Formation and Soft Tissue Healing in Dog Bone Lesions
Statement of Problem: Recent literatures show that accelerated Portland cement (APC) and calcium hydroxide Ca (OH)2 may have the potential to promote the bone regeneration. However, certain clinical studies reveal consis...
The Effect of Mouthwashes on Surface Hardness of Dental Ceramics
Statement of problem: The effect of different mouthrinses on the surface characteristics of ceramic materials is not documented. Objectives: The aim of this study was to determine the effect of three mouthrinses, contain...
A Comparison of Push-Out Bond Strength of Two Endodontic Sealers to Root Canal Dentin: An in Vitro Study
Statement of Problem: Adhesion to root canal dentin is one of the necessary characteristics of endodontic sealers. MTA Fillapex (Angelus, Londria, PR, Brazil) is one of the recently introduced MTA-based sealer. Only a li...
Histomorphometric Analysis of Periodontal Tissue Regeneration by the Use of High Density Polytetrafluoroethylen Membrane in Grade II Furcation Defects of Dogs
Statement of Problem: There are limited histomorphometric studies on biologic efficacy of high density tetrafluoroethylen (d-PTFE) membrane. Objectives: To investigate the healing of surgically induced grade II furcation...